1 knot problems
Phenomenon: in the knotting process, line slip from the hook mouth SP-F-004/SP-F-005, which is in line hook halfway out.
Reason: Dial line hook head SP-B-026 position is too high can not lead to pull the line all hook hook into mouth SP-F-004/SP-F-005.
Solution: loosened line knife pressure two M5 block on the SP-B-027 inner six angle screw, will dial the line hook head SP-B-026 in counterclockwise direction is adjusted downward to the correct position, after locking the M5 inner six angle screws.
The phenomenon: when the phenomenon: when the pull wire knife in SP-B-023 under the pressure of the process, from the line over the hook mouth SP-F-004/SP-F-005, lead line cannot be dialed line hook SP-B-026 hook.
The reason: the thread cutter SP-B-023 position is too high, will not lead to line pressure to the working height of hook mouth SP-F-004/SP-F-005.
Solution: loosened line knife pressure two M5 block on the SP-B-027 inner six angle screw, wire cutter SP-B-023 will dial counterclockwise down regulation to the correct position, after locking the M5 inner six angle screws.
Phenomenon: in the knotting process, often play a single node or dropped the case.
Cause (1): Dial line hook head SP-B-26 position is too low, resulting in in the hook line, hook line level is too serious, to pull off the line.
Solution: loosened line knife pressure two M5 block on the SP-B-027 inner six angle screw, hook line head SP-B-26 will dial clockwise to adjust to the correct position, after locking the M5 inner six angle screws.
The reason (2): tie and dial line does not keep pace.
Solution: open the box on the left side of the machine cover, loosen the synchronous wheel on SP-G-014-V1 expansion sleeve, regulating synchronous wheel SP-G-014-V1 to a suitable location, then the expansion sleeve lock.
The reason: (3) the line was stuck in the process of delivery.
Solution: check whether the line is stuck or clamped in the conveying way, make the line friction to a minimum.
The reason: (4) the surface of the wire is too rough (wire diameter coarse case)
Solution: in wire feeder and lubricants, or other material change good rope.
Phenomenon: in the work process, the knot tail of rabbit ears.
Reason: scissors SP-E-011 shear line too late to end too long, the formation of rabbit ears.
Solution: SP-E-011 scissors cam along the rotation direction of the adjustment, in the knot after the cut line ahead of time.
Phenomenon: in the working process, after the end of, the suspension can not be normal to hang the splint SP-H-001/SP-H-002, but hanging hook in the mouth SP-F-004/SP-F- 005
Reasons: Dial knife SP-B-023 and SP-B-026 adjustment too, leading to tag clip SP-D-078/SP-D-079 backhaul margin to the line too much, coming off from the above easily.
Solution: loosened wire knife pressing block SP-B-027 on the two inner six angle screw, wire cutter will dial SP-B-023 and dial line hook head SP-B-26 in a clockwise direction to the proper position.
Reason: SP-F-004/SP-F-005 mouth hook hook line earlier, the tag clip SP-D-078/SP-D-079 return the margin is too large
Solution: open the box on the left side of the machine, loosen the synchronous wheel on SP-G-014 expansion sleeve, adjust the direction of rotation of the SP-G-014-V1 synchronous wheel move it a little bit, then lock locking can be set
2 scissors problem:
The phenomenon of scissors after, can not return to the correct position.
The reason: the scissors SP-E-010 pad is too thick, stuck to the scissors reset.
Solution: remove or reduce gasket fixed scissors behind SP-E-010
Reason: scissors reset spring SP-E-001 vector.
Resolution: the replacement of a new spring SP-T-001.
The phenomenon of scissors: continuous line.
Reason: SP-E-010/SP-E-011 wear scissors.
Solution: the blade part of repair or replacement of SP-D-010/SP-E-011 scissors, scissors.
Reasons: two M8 locking nuts with scissors SP-E-010/SP-E-011 behind the loose, resulting in two pieces of gap.
Solution: the self-locking nut two M8 lock.
The phenomenon of scissors when cutting line, not completely closed, not to cause shear line.
Reason: the axial shear line offset cam position, leading to stroke, scissors not pushed in place. Solution: loosen the scissors on the cam M8 inner six angle screw, make it to the left along the axial direction slightly adjusted to the correct position after the M8 inner six angle pin screw tightly.
3 punching line
Phenomenon: in the working process, thread pinhole not prick the hole, leading to a bad bar.
Reason: punch die SP-D-046 punch position due to incorrect installation holes perpendicular to the direction of movement of the tag generated error.
Solution: loosen the pressure module on the SP-D-093 M6 in the six corners of the screw, re adjust the position of the punch die.
Reason: to thread a needle SP-B-031 is not correctly installed under the lead, with tag location outside the hole.
Solution: loosen the threading needle bar SP-B-013 M5 inner six angle screw, re calibrated to thread a needle SP-B-031 position, then lock the M5 inner six angle screws.
The reason: pushing the main connecting rod SP-A-011 position shift, resulting in tag clip SP-D-040/SP-D-041 travel change.
Solution: open the rear cover of the machine with 17 in hand to release rocker SP-A-010 screw SP-A-018 M10 nut, up or down slightly adjusting the height of screw SP-A-018, tuned to the correct position can be. If a good tune that clip SP-D-040/SP-D-041 and other parts of the collision can be considered the main thrust regulating connecting rod length of SP-A-011, ensure the clip SP-D-040/SP-D-041 stroke and the starting point to correct.
4, feeder problem
Phenomenon: when the yarn feeder slot line is exhausted, the yarn feeder does not turn.
The reason (1): Transformer feeder and feeder body